- 您现在的位置：买卖IC网 > Sheet目录1210 > DLP-USB245M-G (DLP Design Inc)MODULE USB-TO-TTL PARL FIFO CONV
DLP-USB245M User Manual
9
10
11
12
13
SND/WUP (In) If the DLP-USB245M is in USB suspend, a positive edge on this pin (WAKEUP)
initiates a remote wakeup sequence. If the device is active (not in suspend) a positive edge on this
pin (SEND) causes the data in the write buffer to be sent to the PC on the next USB Data-In request
regardless of how many bytes are in the buffer.
VCC-IO (In) 3.0 volt to +5.25 volt VCC to the UART interface pins 10..12, 14..16 and 18..25.
When interfacing with 3.3v external logic connect VCC-IO to the 3.3v supply of the external logic,
otherwise connect to VCC to drive out at 5v CMOS level. This pin must be connected to VCC from
the target electronics or EXTVCC.
EXTVCC – (In) Use for applying main power (4.4 to 5.25 Volts) to the module. Connect to
PORTVCC if module is to be powered by the USB port (typical configuration)
PORTVCC - (Out) Power from USB port. Connect to EXTVCC if module is to be powered by the
USB port (typical configuration). 500mA maximum current available to USB adapter and target
electronics if USB device is configured for high power.
RXF# - (Out) When low, at least 1 byte is present in the FIFO’s 128-byte receive buffer and is ready
to be read with RD#. RXF# goes high when the receive buffer is empty.
14
TXE#
- When high, the FIFO’s 385 byte transmit buffer is full, or busy storing the last byte written.
Do not attempt to write data to the transmit buffer when TXE# is high.
15
16
17
18
19
20
21
22
23
24
WR (In) When taken from a high to a low state, WR reads the 8 data lines and writes the byte into
the FIFO’s transmit buffer. Data written to the transmit buffer is sent to the host PC within the TX
buffer timeout value ( default 16mS ) and placed in the RS-232 buffer opened by the application
program. Note : The FT245BM allows the TX buffer timeout value to be reprogrammed to a value
between 1 and 255mS depending on the applicaton requirement, also the SND pin can be used to
send any remaining data in the TX buffer regardless of the timeout value.
RD# (In) When pulled low, RD# takes the 8 data lines from a high impedance state to the current
byte in the FIFO’s receive buffer. Taking RD# high returns the data pins to a high impedance state
and prepares the next byte (if available) in the FIFO to be read.
D7 I/O Bi-directional Data Bus Bit # 7
D6 I/O Bi-directional Data Bus Bit # 6
D5 I/O Bi-directional Data Bus Bit # 5
D4 I/O Bi-directional Data Bus Bit # 4
D3 I/O Bi-directional Data Bus Bit # 3
D2 I/O Bi-directional Data Bus Bit # 2
D1 I/O Bi-directional Data Bus Bit # 1
D0 I/O Bi-directional Data Bus Bit # 0
Copyright ? DLP Design 2002
Page 7 of 15
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DLP-USB245R
MODULE USB-TO-PARL FIFO 18-DIP
DM163001
BOARD DEMO PICDEM-1
DM163004-LT
BOARD DEMO PICDEM.NET
DM163005
KIT EVAL PIC16C432/433 LIN BUSS
DM163007
PICDEM CAN-LIN 1 FOR 18C658/858
DM163008
KIT MCP2120/2150 FOR IRDA COMM
DM163010
BOARD DEMO PICDEM USB
DM163012
BOARD DEMO PICDEM FOR 16C781/782
相关代理商/技术参数
DLP-USB245R
功能描述:界面模块 USB-TO-PARALLEL FIFO INTERFACE MODULE
RoHS:否 制造商:4D Systems 产品:Serial Converters 通道/端口数量: 数据速率: 接口类型:USB, UART 工作电源电压:3.3 V, 5 V 最大工作温度:
DLP-UT1
功能描述:工业温度传感器 TEMPERATURE SENSOR RoHS:否 制造商:Texas Instruments 准确性:1 C 功能:Temperature Sensing 25 摄氏度时的电阻: 温度范围:- 55 C to + 127 C 电源电流: 电源电压:2.7 V to 5.5 V
DLP-UTH8
功能描述:数据记录与采集 DLP SENSOR HUB
RoHS:否 制造商:Lantronix 描述/功能:Analog device server 显示器类型:None 电流额定值:
DLPVA-100-F
制造商:未知厂家 制造商全称:未知厂家 功能描述:Low Frequency Voltage Amplifier
DLPVA-100-F-D
制造商:未知厂家 制造商全称:未知厂家 功能描述:Low Frequency Voltage Amplifier
DLPVA-100-F-S
制造商:未知厂家 制造商全称:未知厂家 功能描述:Low Frequency Voltage Amplifier
DLP-VLOG
功能描述:其他开发工具 DEV KIT W/VINCULUM USB HOST CONTRLER IC
RoHS:否 制造商:Parallax 产品:ELEV-8 Hex Upgrade Kits 类型:Robotics 工具用于评估:ELEV-8 Quadcopter 工作电源电压:
DLP-VLOG-OG
制造商:DLP Design 功能描述:VLOG MODULE